hardness test —. Part 1: Test method. Matériaux métalliques — Essai de dureté Vickers —. Partie 1: Méthode d’essai. STANDARD. ISO. Fourth edition. ISO INTERNATIONAL. STANDARD. ISO. Third edition. Metallic materials — Vickers hardness test —. Part 1: Test method. Matériaux . I.S. EN ISO is the adopted Irish version of the European . The text of ISO has been approved by CEN as EN ISO.

Author: Moogukasa Sall
Country: Portugal
Language: English (Spanish)
Genre: Travel
Published (Last): 21 July 2010
Pages: 69
PDF File Size: 10.85 Mb
ePub File Size: 15.70 Mb
ISBN: 731-7-88340-270-7
Downloads: 89531
Price: Free* [*Free Regsitration Required]
Uploader: Meztisar

The Vickers hardness test is specified in this part of ISO for lengths of indentation diagonals between 0, mm and 1, mm. For automated measuring systems this standard should be applied accordingly.

Verlag Berliner Union Stuttgart,pp Care should be taken, if standard uncertainties of type A and B are summarised, that the contributions are not counted twice see Clause 4 of GUM: Need more than one copy? In this case, an estimate of type A standard uncertainty may be obtained from the statistical oso of repeated indentations into the test piece. The correction factors are tabulated in terms of the ratio of the mean diagonal d of the indentation to the diameter D of the cylinder.

HV 2,5 24,52 N may be used. The correction factors are tabulated in terms of the ratio of the mean diagonal d of the indentation to the diameter D of the sphere. Already Subscribed to this document. The work of preparing International Standards is normally carried out through ISO technical committees.

The error is no longer in the calculation of the uncertainty 6057-1 all determined hardness values have to be corrected by b or Ucorr has to be increased by b. In GUM, it is recommended to use a correction to compensate for such systematic effects. This standard is not included in any packages. Please first log in with a verified email before subscribing to alerts.

The required thickness is given by the point of intersection of the minimum thickness scale and a line shown dotted in the example in Figure A.

  IAPT MDS PDF

The procedure for the determination of U is explained in Table D. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Details of the software products used to create this PDF file can be found in the 65507-1 Info relative to the file; the PDF-creation parameters were optimized for printing.

In downloading this file, parties accept therein the responsibility of not infringing Adobe’s licensing policy. The finish of the surface shall permit accurate determination of the diagonal length of the indentation. Your Alert Profile lists the documents that will be monitored.

BS EN ISO 6507-1:2018

The chain starts at the international level using international definitions of the various hardness scales to carry out international intercomparisons.

ISO consists of the following parts, under the general title Metallic materials — Vickers hardness test: NOTE Other values e.

NOTE 1 A strict comparison of hardness 6507- is only possible at identical test forces.

Standards Subscriptions from ANSI provides a money-saving, multi-user solution for accessing standards. It should be noted that for anisotropic materials, for example those which have been heavily cold-worked, there will be a difference between iao lengths of the two diagonals of the indentation.

Such conversions, therefore, should be avoided, unless a reliable basis for conversion can be obtained by comparison tests.

NOTE There is evidence 6507- some materials may be sensitive to the rate of straining which causes small changes in the value of the yield strength. The time from the initial application of the force until the full test force is reached shall not be less than 2 s nor greater than 8 s.

The duration of the test force shall be 10 s to 15 s, except for tests on materials whose time-dependent properties would make this an unsuitable range. Ihre Klassifizierung und 6570-1 auf die Messwerte.

ISO : 金属维氏硬度试验 第一部分:试验方法 – MBA智库文档

Naturally, direct calibration and the is of these machines should be at the highest possible accuracy. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. The specification for the product may indicate limits for the differences between the lengths of the two diagonals.

  ASA MI ASAMI PU LA PDF

Werkstofftechnik 4pp. It may not always be possible to quantify all the identified contributions to the uncertainty. In accordance with Adobe’s licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee.

There is no general process of accurately converting Vickers hardness into other scales of hardness or into tensile strength. The distance between the centres of two adjacent indentations shall be at least three times the mean diagonal length of the indentation in the case of steel, copper and copper alloys, and at least six times the mean diagonal length in the case of light metals, lead and tin and their alloys. The main task of technical committees is to prepare International Standards.

VDI-Berichte 11pp. Add to Alert PDF. Subscription pricing is determined by: It is strongly recommended that this procedure be applied for a maximum of one year after the successful passing of a direct verification. The error b step 10 can be expected to be a systematic effect. If the difference is greater, this shall be stated in the test report. For these tests, a longer duration is permitted and this duration shall be specified as part of the hardness designation see EXAMPLE in 4.

A guideline for the determination is given in Annex D. No deformation shall be visible at the back of the test piece after the test.